top of page
綠色和紅色電線

Wire Flex & Reliability Testing — MAEDEN In-House Lab

Cable flex life is not a single cycle number. Conductor construction, bend radius, angle, load, speed, insulation, strain relief, and installation all change when and how a wire fails. MAEDEN runs bend, torsion, pull, push, circling, and environmental tests in an in-house reliability lab against our own internal standards, with conditions stated on every report—so designs can be compared under defined mechanical and electrical criteria, not marketing adjectives.

MAEDEN-pulling

01
Pulling

MAEDEN-bending

02
Bending

MAEDEN-twisting

03
Twisting

MAEDEN-pushing

04
Pushing

MAEDEN-circling

05
Circling

MAEDEN-fatiguing

06
Others

01 PULLING

Pull / tensile testing

Pull (tensile) testing applies axial force to the conductor or to a crimped / soldered termination until slip or break. Use it to qualify terminals and to measure break load of tinsel, strand, or braid constructions. Fixtures typically include a test stand, load cell, and grips; increase load in a controlled ramp and record peak force and failure mode.

MAEDEN-Comp_pulling

Wire pull testers are easy to use. They have three main parts; the test stand, the load sensor and the gripping attachment. To perform the test, you should feed one end of the wires to the gripping attachment. The other end goes to a fixed point and is secured. The tester will gradually pull the wire, increasing the force until either the terminal is removed or the wire breaks.

02 BENDING

Bend testing

Bend testing measures how a wire or finished cable behaves under repeated flex. MAEDEN fixtures allow adjustable load, radius, angle / stroke, and speed. Programs may stop at a continuity or resistance limit (non-destructive monitoring) or continue to mechanical break when the plan requires it.

Parameters to agree before a run:

- Sample length, preparation, and termination
- Radius (R), angle, load, speed / rpm
- Electrical monitor (continuity, resistance threshold)
- Cycle count target or run-to-fail
- Temperature / humidity if not ambient

MAEDEN-Comp_bending

You can take a sample material to a certain limit to make it bend. Finding out what is the load limit that makes a material bend is a non-destructive test because it does not push the wire to destruction. It only finds the limit before the wire breaks. For the second test, bend the material until it breaks or determine the load and deflection needed to achieve a break limit. This is the destructive test.

 

At Maeden, we tend to do non-destructive tests, though sometimes we conduct some destructive testing. Our test results are usually cyclical, and we record how a wire behaves after a couple rounds of testing. The parameters of our testing are:

Load

We test our wires using a non contact voltage tester. The tester gives a beep when its tip touches voltage or electricity. Some testers can also illuminate a light when they touch voltage.

Radius

The smallest radius a cable may be bent around without getting damaged is known as the cable bending radius. The size, construction, conductor type, and sheathing and insulation types of the cable are all factors that affect the minimum bending radius.

Angles/ Movement

This is done using the wire pull test. It involves applying an upward force pulling the wire from the substrate using a  hook. The pulling is done until you notice a bond failure or the wire breaks.

Speed

We use a power meter for the speed test. A power meter is connected between the cable and USB device like a smartphone. The wire’s charging rate will be displayed on the power meter. You can find out how much power goes through the wire by multiplying voltage by the amperage.

03 TWISTING

Torsion (twist) testing

Torsion testing twists the sample about its axis to assess durability under rotational motion (earbuds, robot joints, rotary interfaces). Record torque, angle, speed, and cycles or angle-to-fail per the agreed plan. Sample gauge length and end fixing must be fixed in the protocol so runs are comparable.

MAEDEN-Comp_twisting

To do the torsion test, place a longitudinal sample in a torsion tester. Twist one end of the sample along its axis until it breaks and record the force, torque or angular displacement.

04 PUSHING

Push and circling tests

A push test is also known as a reverse pull test.

MAEDEN-Comp_pushing

Push applies load in compression or reverse-pull geometry—useful when the application loads the wire opposite to a simple tensile path. Load once or cyclically per plan.

Circling / conical motion uses an in-house multi-axis fixture to sweep the cable through a spatial path that combines bend components—closer to some handheld and device-cable use cases than planar bend alone. Define orbit, speed, and electrical fail criteria in the protocol.

05 CIRCLING

Circle Testing

A circle test on cables and wires is also known as a conical test. The machine to conduct the circle test was developed by Maeden. We usually use this test on Apple devices.

MAEDEN-Comp_circling

06 Others

Other wire and cable tests

Fatigue Test

Wires and cables face constant vibrating, especially in speakers. This means that they are prone to deformation and can be fatigued. You can conduct a fatigue test on our wires and cables to know if your speakers will experience fatigue while in use. Constant/High temperature and humidity test A constant or high temperature test will tell you whether your products will perform well when exposed to high temperatures and humidity.

Constant/High Temperature and Humidity test

A constant or high temperature test will tell you whether your products will perform well when exposed to high temperatures and humidity.

Salt Spray Test

In the car industry, a salt spray test helps to safeguard wires from corrosion. If a car is driven in winter, especially in areas that use salt to melt the snow on the road, the salt may cause corrosion in the wires. To avoid this and ensure our wires are safe from corrosion in the engine, a salt spray test is necessary. The test is conducted to stimulate corrosion and ensure the wires used in the engine will endure the salt used to melt snow on the roads.

Drop Test

You can use the drop test to know what would happen to our cables when they face a sudden acceleration or shock.

Puncture/Penetration Test

Devices made of wires and cables will fail when the wires are punctured. To ensure your products are safe from failure in this way, a puncture or penetration test is important. It ensures your devices will not be easily damaged when they face sharp objects.

Friction Test

If you make products that are in use on a daily basis, like earphones, or charging cables, they will encounter a lot of friction. A friction test on our cables lets you know if your devices can endure constant friction.

bottom of page